AN6 hose has an ID of 8.6mm
AN4 ID is 5.6mm
You could use AN6, however it will not fit 'snugly on every fuel line and will require the use of hose clamps instead of the stock spring clamps.
Anyone considered E85?
Moderators: timk, Stu, zombie, The American, Lokiel, -alex, StanTheMan, greenMachine, ManiacLachy, Daffy, Sean
-
- Speed Racer
- Posts: 7468
- Joined: Fri Feb 11, 2011 12:49 pm
- Vehicle: NA6
- Location: Purga, QLD
- StanTheMan
- Forum legend
- Posts: 6824
- Joined: Thu Apr 24, 2003 11:00 am
- Vehicle: NA6
- Location: Balgowlah
Re: Anyone considered E85?
I wasnt planning on doing anything fancy.I was thinking of just replacing the OEM fuel hoses that already exists. Although it would look cool with fancy linkages & braided fuel lines
still trying to get my head around how those fitting work & How thy attach to the metal lines.
AN4 would then be the one to use for a straight swap.
still trying to get my head around how those fitting work & How thy attach to the metal lines.
AN4 would then be the one to use for a straight swap.
Satans Ride called F33nix the resurrected NA6
- CrazyRacer
- Fast Driver
- Posts: 274
- Joined: Sun Sep 28, 2008 5:15 pm
- Vehicle: NB SE
- Location: Gold Coast
Re: Anyone considered E85?
Apparently ethanol molecules are smaller than petrol and can permeate through standard fuel hoses and cause sweat and vapours.
Probably not great on any car but especially bad if you run your fuel lines inside your race car as a few race guys have reported it getting quite fumey.
Best stuff to use is PTFE, but even with this you're supposed to make sure you use carbon impregnated Teflon lines to conduct static electricity so you don't get sparks. Not cheap though!
Probably not great on any car but especially bad if you run your fuel lines inside your race car as a few race guys have reported it getting quite fumey.
Best stuff to use is PTFE, but even with this you're supposed to make sure you use carbon impregnated Teflon lines to conduct static electricity so you don't get sparks. Not cheap though!
- StanTheMan
- Forum legend
- Posts: 6824
- Joined: Thu Apr 24, 2003 11:00 am
- Vehicle: NA6
- Location: Balgowlah
Re: Anyone considered E85?
CrazyRacer wrote:Apparently ethanol molecules are smaller than petrol and can permeate through standard fuel hoses and cause sweat and vapours.
Probably not great on any car but especially bad if you run your fuel lines inside your race car as a few race guys have reported it getting quite fumey.
Best stuff to use is PTFE, but even with this you're supposed to make sure you use carbon impregnated Teflon lines to conduct static electricity so you don't get sparks. Not cheap though!
Ok I've ordered about 5m of some braided teflon fuel hose rated at 250 deg and some PSI rating I'll never need in 10 lifetimes.
Apperntly ths stuff doesnt take on the smell either
I'll replace the fuel filter (which is brand new) in about a months time. I may also check on fuel pump & how dirty the tank may be at around that time.
Satans Ride called F33nix the resurrected NA6
- StanTheMan
- Forum legend
- Posts: 6824
- Joined: Thu Apr 24, 2003 11:00 am
- Vehicle: NA6
- Location: Balgowlah
Re: Anyone considered E85?
Just checked . Turns out it is PTFE
Satans Ride called F33nix the resurrected NA6
- trickytrev
- Driver
- Posts: 69
- Joined: Sat Jan 12, 2013 5:35 pm
- Vehicle: NC - Supercharged
Re: Anyone considered E85?
E85 attracts a lot more moisture so better Oil and more regular oil changes
Blown 300+
-
- Speed Racer
- Posts: 7468
- Joined: Fri Feb 11, 2011 12:49 pm
- Vehicle: NA6
- Location: Purga, QLD
Re: Anyone considered E85?
Been running E85 for a few years now and just swapped out some of the OEM hoses that showed no signs of deterioration or leaking.
These hoses were:
To do my fuel lines I used PFE400R-06BK - Black Push Lock Hose E85/Methanol -06AN from Dirt Devil Industries http://dirtdevilind.com.au/. Dirt Devil has HEAPS of stuff and it is not a safe place to browse in... Bonus, it is on my way home from work so I can order and pick up in the afternoon or it is open on Saturday AM.
An alternative source of fittings/hose is Ian Botecher Race parts (very close to home for me as well) http://ianboettcherraceparts.com.au/ they are a stockist of Aeroflow. Only issue with Ian Botecher is that the safety gear they sell (seats/suits/harness/etc) are geared towards speedway and are not always FIA compliant. Some CAMS events (WTAC) do not accept SFI-3.3/5 footware.
These hoses were:
- Tank to hard line (feed/return)
- Feed either side of the fuel filter
To do my fuel lines I used PFE400R-06BK - Black Push Lock Hose E85/Methanol -06AN from Dirt Devil Industries http://dirtdevilind.com.au/. Dirt Devil has HEAPS of stuff and it is not a safe place to browse in... Bonus, it is on my way home from work so I can order and pick up in the afternoon or it is open on Saturday AM.
An alternative source of fittings/hose is Ian Botecher Race parts (very close to home for me as well) http://ianboettcherraceparts.com.au/ they are a stockist of Aeroflow. Only issue with Ian Botecher is that the safety gear they sell (seats/suits/harness/etc) are geared towards speedway and are not always FIA compliant. Some CAMS events (WTAC) do not accept SFI-3.3/5 footware.
- NitroDann
- Forum sponsor
- Posts: 10280
- Joined: Thu Nov 05, 2009 12:10 pm
- Vehicle: NA6
- Location: Newcastle NSW
- Contact:
Re: Anyone considered E85?
Craig or whatever his name is at Dirt devil must be g*y based on the amount of times he has f*cked me. willnotrecommend/10
Dann
- edit Okibi 22/3 9pm WST post reported to be offensive -
Dann
- edit Okibi 22/3 9pm WST post reported to be offensive -
http://www.NitroDann.com
speed wrote:If I was to do it again, I wouldn't even consider the supercharger.
-
- Speed Racer
- Posts: 7468
- Joined: Fri Feb 11, 2011 12:49 pm
- Vehicle: NA6
- Location: Purga, QLD
Re: Anyone considered E85?
Interesting observation Dann.
If i based my recommendation on salesmanship then I would have to agree with you, he is not the most personable person to buy off. However he carries good stock levels, price is reasonable and is close to home. He even allowed the return unused fittings, cannot complain about that.
If i based my recommendation on salesmanship then I would have to agree with you, he is not the most personable person to buy off. However he carries good stock levels, price is reasonable and is close to home. He even allowed the return unused fittings, cannot complain about that.
- NitroDann
- Forum sponsor
- Posts: 10280
- Joined: Thu Nov 05, 2009 12:10 pm
- Vehicle: NA6
- Location: Newcastle NSW
- Contact:
Re: Anyone considered E85?
Via ebay... no fun at all.
Dann
Dann
http://www.NitroDann.com
speed wrote:If I was to do it again, I wouldn't even consider the supercharger.
Return to “MX5 Forced induction (Turbo/Supercharger)”
Who is online
Users browsing this forum: No registered users and 103 guests