[BNE] Dodgy Day Round 4 Saturday 29th November

[Steampunk]

Howdy all for more detail please refer to this thread:

http://mx5cartalk.com/forum/viewtopic.php?f=62&t=65531

Please keep comments and banter to the other thread, I just wanted to start this one because not everyone here is aware or check the "events" section, and just to get list of names and what they are bringing with them, what they are wanting done etc.

If we can all bring food enough for 2 people, then there'll be plenty

Please add/amend to the list below.

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services

Big Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
ManiacLachy - Foamectomy. Any attendees willing to help with this?
slug_dub - Frame rails and butterfly brace
slug_dub - Twin hoop bar


Detailing required:
Magpie's NA6

gslender tuning help:
slug_dub (MS3 possibility)
ausbuoy (MS2)
Jelzahar

[Nevyn72]

Don't forget dismantling Magpie/Gslender's newly aquired NA6.

[Gladiator]

Actually Magpies/Gladiators newly acquired NA6.
I'm bringing engine crane ,stands, jack, rattle gun, assorted tools & I'll bring a carton of coke again.


Sent from my iPhone using Tapatalk

[ManiacLachy]

Scratch the foamectomy from the list, but intercooler and coilovers are a go!

[pezchops]

lilly and i are going..
ive got more than enough 2mm sheet aluminium ,bits and pieces for inter-cooler brackets so if anyone else needs similar its there.
Magpie has a guillotine and folder ?
Im just trying on a set of 15ins wheels and general help if needed.

[corners]

lilly and i are going..
ive got more than enough 2mm sheet aluminium ,bits and pieces for inter-cooler brackets so if anyone else needs similar its there.
Magpie has a guillotine and folder ?
Im just trying on a set of 15ins wheels and general help if needed.

Enough for an air box

[Magpie]

I have a 720mm metal folder but no guillotine.

[Steampunk]

Aaargh.. guys... please just limit this thread to copy/paste and adding/amending the below list or else it will blow out to a dozen pages;

Also forgot to add, please PM me for Magpie's address


steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
ManiacLachy - Foamectomy. Any attendees willing to help with this?
slug_dub - Frame rails and butterfly brace
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R

gslender tuning help:
slug_dub (MS3 possibility)
ausbuoy (MS2)
Jelzahar

[ManiacLachy]

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, softdrink

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Frame rails and butterfly brace
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?

gslender tuning help:
slug_dub (MS3 possibility)
ausbuoy (MS2)
Jelzahar[/quote]

15" Wheel testing:
Pezchops
ManiacLachy

[Magpie]

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks, 720mm metal folder, gas bottle for Webber Q
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, softdrink

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Frame rails and butterfly brace
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?

gslender tuning help:
slug_dub (MS3 possibility)
ausbuoy (MS2)
Jelzahar[/quote]

15" Wheel testing:
Pezchops
ManiacLachy[/quote]

[Gladiator]

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks, 720mm metal folder, gas bottle for Webber Q
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, softdrink

Gladiator - Many cold cans of coke.

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Frame rails and butterfly brace
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?

gslender tuning help:
slug_dub (MS3 possibility)
ausbuoy (MS2)
Jelzahar

15" Wheel testing:
Pezchops
ManiacLachy




Sent from my iPhone using Tapatalk

[slug_dub]

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks, 720mm metal folder, gas bottle for Webber Q
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, softdrink

Gladiator - Many cold cans of coke.

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?

gslender tuning help:
ausbuoy (MS2)
Jelzahar

15" Wheel testing:
Pezchops
ManiacLachy

[NASilverStone]

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks, 720mm metal folder, gas bottle for Webber Q
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, softdrink

Gladiator - Many cold cans of coke.

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6


Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?

gslender tuning help:
ausbuoy (MS2)
Jelzahar

15" Wheel testing:
Pezchops
ManiacLachy

Visiting only:
NASilverstone

[NZMiata]

Finally a Dodgy Day that I can attend!

steampunk - 3kg chicken wings, hot sauce, tools, car stands, witty banter
corners - WeberQ
magpie - venue, water, shade, camera, witty banter, 6 car stands, 2 ramps, large and small trolley jacks, 720mm metal folder, gas bottle for Webber Q
Crapweasel - a buffer, a bunch of polishing pads, microfibre cloths and an array of polishing products.
Corners - possible buffing services
Tezzax5 - RRiiiibbbbsss!!!
ManiacLachy - chips, soft drink
NZMiata - sausages and bread
Gladiator - Many cold cans of coke.

Jobs
ManiacLachy - Coilovers (+ corner weight). No issues doing this, take about 4 hours at a rough guess.
ManiacLachy - Intercooler. What do you need done, Lokiel has lots of experience in this area. Would need to be done after coilovers/corner weight.
slug_dub - Twin hoop bar
pezchops - trying on a set of 15ins wheels and general help if needed, cutting/making brackets.
Gladiator/Magpie - dismantling NA6
NZMiata - Locate (and maybe fix) a slow power steering fluid leak

Detailing required:
Magpie's NA6
Steampunk's GTi-R
ManiacLachy - some scratches on the boot from PO that might be able to be buffed out?
NZMiata - see if we can improve the slightly dodgy paint on the bonnet

gslender tuning help:
ausbuoy (MS2)
Jelzahar

15" Wheel testing:
Pezchops
ManiacLachy

Visiting only:
NASilverstone

[taminga16]

It would be lovely if everyone could take a moment to remember Mickey (Uncle Arthur).
Greg.