All:
Just a quick one.
I want to fit a small amp behind the passenger seat in my NA Clubman.
Am I OK to use 10mm tech screws directly into the rear wall/bulkhead skin or is the fuel tank there?
There would be a couple of screws about 200mm up from the floor about 250mm apart from centre of the wall and about 300mm higher up with the same spacing.
Non of the holes really above the arm rest height on the centre console.
You help would be great.
Thanks
Damon
Amp Behing Passenger Seat
Moderators: timk, Stu, zombie, Andrew, -alex, miata
-
Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Re: Amp Behing Passenger Seat
When I had an amp in my nb. I used Velcro to stick it there
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
Nevyn72
- Speed Racer
- Posts: 2189
- Joined: Fri Nov 29, 2013 8:51 am
- Vehicle: ND - RF
- Location: Sydney
Re: Amp Behing Passenger Seat
You'd want to be careful, the fuel tank is behind that bulkhead! 
"A Convertible has a top you can put down when the weather's nice...... A Roadster has a top you can put up when the weather's bad."
-
bear2230
- Racing Driver
- Posts: 1627
- Joined: Thu Jul 01, 2010 11:43 pm
- Vehicle: NB SP
- Location: Sydney South, God's country.
- Contact:
Re: Amp Behing Passenger Seat
Regie wrote:When I had an amp in my nb. I used Velcro to stick it there
Qantas Engineer says use Velcro........Use Velcro.
Scooby - Silver SP - Build # 53
Snowie - White NB project car. Engineered and registered
Vader - Hilux & Gretel the black German Bitch
-
Damon Clubman
- Driver
- Posts: 27
- Joined: Mon Mar 26, 2012 11:18 pm
Re: Amp Behing Passenger Seat
Velcro it is!
Ask first and then drill/screw later if Ok'd
Ask first and then drill/screw later if Ok'd
-
Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Re: Amp Behing Passenger Seat
bear2230 wrote:Regie wrote:When I had an amp in my nb. I used Velcro to stick it there
even found a pic
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
and1
- Fast Driver
- Posts: 368
- Joined: Sat Sep 18, 2010 9:43 pm
- Vehicle: NB SE
- Location: Perth, WA
Re: Amp Behing Passenger Seat
On my SE there are a couple of welded nuts on that rear bulkhead. I put bolts through them to hold a piece of mdf that my amp was attached to.
-
Jeo
- Speed Racer
- Posts: 3648
- Joined: Thu Jun 26, 2008 9:33 am
- Vehicle: NB8B
- Location: Canberra
Re: Amp Behing Passenger Seat
I used velcro in the same place.
Return to “MX5 Audio, Electronics & Lighting”
Who is online
Users browsing this forum: No registered users and 102 guests
