Installing an SE Torsen diff into SP

Engines, Transmissions & Final Drive questions and answers

Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy

Post Reply
User avatar
green_comet
Car Detailing Guru
Posts: 1848
Joined: Tue May 24, 2005 1:41 am
Vehicle: NA8
Location: Melbourne

Installing an SE Torsen diff into SP

Postby green_comet » Sun Mar 30, 2014 12:00 am

Hey guys,

Just a few quick questions.

I'm looking at picking up an SE torsen diff and housing for my SP, I just wanted to know if others have done this install (even on a standard NB8B) and if they could offer any info on what's involved.

Doing some research on here, it seems that the SE's torsen and the SP's open diff are the same ratio at 3.63, can anyone confirm this?

After doing some more reading here, it seems that the SE and SP axles are a different spline count. 28 splines on the SE's axles and 26 on the SP and standard NB8B, can anyone confirm this?

If this is the case, is there any way to use my standard SP axles for the install, or would I need to source SE axles and swap them over before i could install the diff/housing?

Any help is very much appreciated.

Cheers
Ryan
Top
User avatar
Okibi
Speed Racer
Posts: 10899
Joined: Thu Aug 21, 2003 11:00 am
Vehicle: NB SE
Location: Perth, Western Australia
Contact:
Contact Okibi

Re: Installing an SE Torsen diff into SP

Postby Okibi » Sun Mar 30, 2014 1:16 am

Grab the axles as well.

Aussie SEs had the same ratio as your SP

http://www.mx5cartalk.com/SP_SE_Comparison/
If you had access to a car like this, would you take it back right away? Neither would I.
Top
User avatar
de Bounce
Racing Driver
Posts: 1091
Joined: Thu Feb 12, 2009 5:19 pm
Vehicle: NC
Location: Northern Burbs - Melbourne

Re: Installing an SE Torsen diff into SP

Postby de Bounce » Sun Mar 30, 2014 6:56 am

You WILL need to use the SE axles
When you (eventually) remove the axles from the uprights/hubs you also need to discard the dust seals (not used on the SE)
2011 NC2 PRHT SE in Dolphin Grey
2001 NB8B in Crystal Blue - Sold :(
Motorkhana Video
Top
User avatar
davekmoore
Speed Racer
Posts: 4681
Joined: Thu Apr 30, 2009 1:53 am
Vehicle: NC
Location: Esprick, UK

Re: Installing an SE Torsen diff into SP

Postby davekmoore » Sun Mar 30, 2014 9:24 am

Over 9 hours and no complaints yet about putting SE bits in a SP?
UK since return: Standard NC2 (horrid), C200K, ND2 BBR, NC2 BBR200 (loved it), NC BBR300 (better than BARMY), V-Special, turbo NB8B (my 84th car)
Top
User avatar
green_comet
Car Detailing Guru
Posts: 1848
Joined: Tue May 24, 2005 1:41 am
Vehicle: NA8
Location: Melbourne

Re: Installing an SE Torsen diff into SP

Postby green_comet » Sun Mar 30, 2014 12:25 pm

Sweet as guys, thanks for the help. Everything is sorted. :beer:
Top
User avatar
NitroDann
Forum sponsor
Posts: 10280
Joined: Thu Nov 05, 2009 12:10 pm
Vehicle: NA6
Location: Newcastle NSW
Contact:
Contact NitroDann

Re: Installing an SE Torsen diff into SP

Postby NitroDann » Sun Mar 30, 2014 3:47 pm

davekmoore wrote:Over 9 hours and no complaints yet about putting SE bits in a SP?


Glorified turbo nb8as lol.

Dann
http://www.NitroDann.com

speed wrote:If I was to do it again, I wouldn't even consider the supercharger.
Top
Post Reply

Return to “MX5 Engines, Transmission & Final Drive”

Who is online

Users browsing this forum: No registered users and 52 guests