Hi Guys,
Funny problem that I've had for quite a while. I usually just drive around it (more throttle), but it's a bit of a pain sometimes.
Car runs great, revs out, plenty of power.
Often when I'm cruising along in gear with little or no throttle and then give it a bit of a squirt, the car hesitates before taking off. Between 2k and 4k RPM. Above that, no issues. If i take off from idle and run up through the gears it doesn't happen at all.
Have a JR CAI and Xforce extractors. Happened to a similar extent on stock intake and exhaust. Plugs are new, leads are new.
Should I be investigating coils/igniter? I can probably borrow some for testing. Anything else I should be looking at?
Cheers
B6 Bogging 2k-4k - Closed throttle > WOT
Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy
-
- Driver
- Posts: 90
- Joined: Thu Nov 17, 2011 10:57 pm
- MrRevhead
- Racing Driver
- Posts: 715
- Joined: Mon Mar 26, 2012 2:40 pm
- Vehicle: NA6
- Location: NW Sydney
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Cleaned the flapper on the AFM or throttle body butterfly recently?
No leaks around the intake? (clamps on tight, rubber joiners in good condition etc)
No leaks around the intake? (clamps on tight, rubber joiners in good condition etc)
1991 NA6 BRG Limited Edition #124 (Aus Delivered)
-
- Driver
- Posts: 90
- Joined: Thu Nov 17, 2011 10:57 pm
Re: B6 Bogging 2k-4k - Closed throttle > WOT
clamps and joiners are fine.
I guess I'll give the afm flapper and butterfly a clean with carby cleaner. Since I don't own a car with a carb any more I might as well use it for something.
I guess I'll give the afm flapper and butterfly a clean with carby cleaner. Since I don't own a car with a carb any more I might as well use it for something.
-
- Fast Driver
- Posts: 471
- Joined: Thu Dec 19, 2013 10:36 pm
- Vehicle: NA6
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Skyntara wrote:clamps and joiners are fine.
I guess I'll give the afm flapper and butterfly a clean with carby cleaner. Since I don't own a car with a carb any more I might as well use it for something.
Not sure if it applies here but hotwires don't like car by cleaner. There's electronic's safe stuff which I've used successfully (contact cleaner).
-
- Fast Driver
- Posts: 423
- Joined: Thu May 19, 2011 11:10 am
- Vehicle: ND - 2
- Location: brisbane
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Hi.
I will try again.
Do not use carby cleaner on the butterfly it will remove the sealer. Use only throttle body cleaner,
I will try again.
Do not use carby cleaner on the butterfly it will remove the sealer. Use only throttle body cleaner,
-
- Driver
- Posts: 90
- Joined: Thu Nov 17, 2011 10:57 pm
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Guess I'm stuck with the carby cleaner a bit longer then.
Off to get some throttle body cleaner
Off to get some throttle body cleaner
-
- Speed Racer
- Posts: 3722
- Joined: Sun Jan 18, 2009 10:16 pm
- Vehicle: Non MX-5
- Location: Glasshouse Mountains, QLD
Re: B6 Bogging 2k-4k - Closed throttle > WOT
check the leads and coils aren't earthing out before the spark gets to the plugs.
-
- Speed Racer
- Posts: 11854
- Joined: Mon Aug 08, 2005 11:35 pm
- Vehicle: Clubman
- Location: Melbourne
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Washed the motor lately or has water got into the upper engine bay? See Droo's post in following:
viewtopic.php?f=55&t=57190&p=720469&hilit=na%2A+hesitat%2A+accelerat%2A#p720469
viewtopic.php?f=55&t=57190&p=720469&hilit=na%2A+hesitat%2A+accelerat%2A#p720469
-
- Driver
- Posts: 90
- Joined: Thu Nov 17, 2011 10:57 pm
Re: B6 Bogging 2k-4k - Closed throttle > WOT
Motor is very dry.
Never wash the outside of the car, let alone the engine bay.
Never wash the outside of the car, let alone the engine bay.
Return to “MX5 Engines, Transmission & Final Drive”
Who is online
Users browsing this forum: No registered users and 104 guests