Dodgy Day round 2: 16th June 2013

KIMO · Postby **KIMO** » Fri Jun 14, 2013 10:15 pm

sorry guys, last minutes question...
Would any1 know if its easy or hard to install and AGI roll bar??? how long approx?

Timbo · Postby **Timbo** » Sat Jun 15, 2013 12:55 am

The soft top is partially on the frame? Haha it's a bit of a mess...

Crapweasel · Postby **Crapweasel** » Sat Jun 15, 2013 1:34 am

Not going to be able to make it, but looks like that's a good thing though, plenty more important stuff to be done, post pics!!!

Have fun guys!

Cheers
Pete

CaptainNate · Postby **CaptainNate** » Sat Jun 15, 2013 3:44 am

Picked up the clutch and flywheel today!

Just gotta pop into a store and buy the oils today sometime.
What oils/brands do peoples recommend for the transmission and clutch? (Should I do the diff as well while I'm under there or can that wait?)

Magpie · Postby **Magpie** » Sat Jun 15, 2013 4:36 am

KIMO wrote:sorry guys, last minutes question...
Would any1 know if its easy or hard to install and AGI roll bar??? how long approx?

Not sure how long it would take but it should be able to be done. What time will you be arriving? We would just need to plan out who needs what done.

CaptainNate · Postby **CaptainNate** » Sat Jun 15, 2013 6:22 am

Urgent request! Does anyone have a Clutch Alignment tool they can bring along for me to borrow?!
Skipped my mind when I was getting things ready

tbro · Postby **tbro** » Sat Jun 15, 2013 7:54 am

CaptainNate wrote:Urgent request! Does anyone have a Clutch Alignment tool they can bring along for me to borrow?!
Skipped my mind when I was getting things ready

1600, visually line up and just tighten bolts so plate doesn't slip but so it can be moved, then just use your fingers to align the outer surface of plate to the pressure plate at the 3 points. I'll show you how tomorrow.

CaptainNate · Postby **CaptainNate** » Sat Jun 15, 2013 7:55 am

Sweet!
The wait is slowly killing me! haha

Postby **mrpham** » Sat Jun 15, 2013 9:54 am

I have clutch alignment tool, and I'll be there at 9.

Postby **mrpham** » Sat Jun 15, 2013 9:56 am

Do you guys need me to bring anything? I'll pack some tools and by wiring/electrical stuff.

sailaholic · Postby **sailaholic** » Sat Jun 15, 2013 10:02 am

mrpham wrote:Do you guys need me to bring anything? I'll pack some tools and by wiring/electrical stuff.

A white na6, with itbs, awesome interior, decent fitment, super short diff and a load of awesome in the boot?

Have fun boys, won't be able to make it.

Sent from my GT-I9100 using Tapatalk 2

Postby **mrpham** » Sat Jun 15, 2013 10:41 am

sailaholic wrote:A white na6, with itbs, awesome interior, decent fitment, super short diff and a load of awesome in the boot?

Have fun boys, won't be able to make it.

Sent from my GT-I9100 using Tapatalk 2

Who has a car trailer?

Steampunk · Postby **Steampunk** » Sat Jun 15, 2013 1:49 pm

- Pham, no need to bring anything special, just the same as last time.

- KIMO, I was wrong about where that vertical end-plate (the L shaped one) goes and, unless my eyes deceive me, I see there are two different designs, one with "L" shaped end plate like yours and one with just a horizontal plate.
I THINK I now know where it goes, but I couldn't find any installation photos to confirm.
If you are able to bring it down, then we can at least drill holes for the front end-plates so the job is half done, then tackle it another time when we know exactly what to do.

Doesn't it come with any fitting instructions?

- Nate, tbro dropped off the end-seal which I'll bring.

Magpie · Postby **Magpie** » Sat Jun 15, 2013 2:11 pm

mrpham wrote:Who has a car trailer?

I have at home why?

KIMO · Postby **KIMO** » Sat Jun 15, 2013 3:14 pm

"Not sure how long it would take but it should be able to be done. What time will you be arriving? We would just need to plan out who needs what done."

will be there around 9ish.

"- KIMO, I was wrong about where that vertical end-plate (the L shaped one) goes and, unless my eyes deceive me, I see there are two different designs, one with "L" shaped end plate like yours and one with just a horizontal plate.
I THINK I now know where it goes, but I couldn't find any installation photos to confirm.
If you are able to bring it down, then we can at least drill holes for the front end-plates so the job is half done, then tackle it another time when we know exactly what to do."

i do, will bring the instruction manual.

I dont have any useful tools, will bring snacks and drinks instead. and help out with what ever needed; including taste testing :beer: