Dodgy Day round 2: 16th June 2013

Gladiator · Postby **Gladiator** » Mon Jun 10, 2013 6:07 am

Dan-mx5 wrote:I was wondering what time the timing light owners were hanging around for?
Won't be able to get there until after 1pm.

Who knows mate? I'd say I'll still be around though.

Magpie · Postby **Magpie** » Mon Jun 10, 2013 6:10 am

Last one finished as the sun was setting.

Steampunk · Postby **Steampunk** » Mon Jun 10, 2013 8:14 pm

THIS SUNDAY BUOYS AND GULLS!

Magpie's place at Upper Coomera is easy to get to from anywhere, and traffic isn't going to be a big schlep.

Ha! "Schlep" doesn't appear as a spelling error :roll:

CaptainNate · Postby **CaptainNate** » Mon Jun 10, 2013 8:24 pm

My 2 cents: WHHOOOOOOO!

Fingers crossed the clutch will be ready in time :shock:

corners · Postby **corners** » Tue Jun 11, 2013 11:56 am

CaptainNate wrote:
corners wrote:Also can't remember if you need a spigot bearing for mx5s?

I remember this being thrown around in another thread but can't for the life of me remember if I should replace it or not.
Yay or nay peoples? If yay, thats the last thing I need!
I'M EXCITES!

As far as I understand its usually done with the clutch.

corners · Postby **corners** » Tue Jun 11, 2013 11:58 am

Does anyone have or bringing drill bits including a large one?
I want to fit a spoiler to my boot but will need a larger bit for the hole for the wiring

Magpie · Postby **Magpie** » Tue Jun 11, 2013 12:16 pm

What size drill bit do you need? I have some step drills that go from 4mm to 20mm or some sheet metal hole saws of various sizes. Beyond that an air panel saw or an air die grinder or a lump hammer and a blade screwdriver.

corners wrote:Does anyone have or bringing drill bits including a large one?
I want to fit a spoiler to my boot but will need a larger bit for the hole for the wiring

corners · Postby **corners** » Tue Jun 11, 2013 12:17 pm

Magpie wrote:What size drill bit do you need? I have some step drills that go from 4mm to 20mm or some sheet metal hole saws of various sizes. Beyond that an air panel saw or an air die grinder or a lump hammer and a blade screwdriver.

corners wrote:Does anyone have or bringing drill bits including a large one?
I want to fit a spoiler to my boot but will need a larger bit for the hole for the wiring

I think the above should help out

Steampunk · Postby **Steampunk** » Wed Jun 12, 2013 12:14 pm

4 more sleeps.

There may be something a bit special that Magpie has rousted up.

I guess only the ones attending will find out what... :wink:

Magpie · Postby **Magpie** » Wed Jun 12, 2013 12:19 pm

Steampunk wrote:There may be something a bit special that Magpie has rousted up.

And it has nothing to do with wiring up gauges (of which I am going to avoid if asked).

Steampunk · Postby **Steampunk** » Wed Jun 12, 2013 12:44 pm

Magpie wrote:
Steampunk wrote:There may be something a bit special that Magpie has rousted up.

And it has nothing to do with wiring up gauges (of which I am going to avoid if asked).

Didn't you say that ALL your tools required for ANY kind of wiring has been sent away for re-calibration so won't be available? :mrgreen: