NitroDann's Long Awaited Garage Thread

sailaholic · Postby **sailaholic** » Fri May 03, 2013 7:44 am

Lokiel wrote:
16bit wrote:i tried to convince him of off the shelf stuff but no dice.

If I bought an off-the-shelf GT2650 kit, I knew that I'd always regret not getting the EFR6258 instead, it spools much faster and generates more power than the GT2560.

Now that it's almost complete, I'm glad I did, it's friggin' awesome!

Having spoken to you in person I can honestly say I think you will be disappointed about 2 months after you've got this back......

Because it still has stock bottom end and knowing you, you will want more! Haha :grin:

Sent from my GT-I9100 using Tapatalk 2

Lokiel · Postby **Lokiel** » Fri May 03, 2013 9:07 am

^
Not for long

Unfortunately until then, it will be like sleeping in the same bed as Salma Hayek but not being able to touch her until the engine is built.

bootz · Postby **bootz** » Fri May 03, 2013 1:26 pm

Thanks Dann, you can learn a shitload round here. For ref, here is the AVO 1.6 mani.

Postby **NitroDann** » Fri May 03, 2013 5:59 pm

sailaholic wrote:
Lokiel wrote:
16bit wrote:i tried to convince him of off the shelf stuff but no dice.

If I bought an off-the-shelf GT2650 kit, I knew that I'd always regret not getting the EFR6258 instead, it spools much faster and generates more power than the GT2560.

Now that it's almost complete, I'm glad I did, it's friggin' awesome!

Having spoken to you in person I can honestly say I think you will be disappointed about 2 months after you've got this back......

Because it still has stock bottom end and knowing you, you will want more! Haha :grin:

Sent from my GT-I9100 using Tapatalk 2

It should do over 400 atw with a built bottom end if i did my job right.

He wont get bored of that haha :twisted:

Dann

Postby **NitroDann** » Fri May 03, 2013 6:34 pm

Manifold is currently at the ceramic shop getting a couple of coats of Turbo X ceramic coat. Build to handle 2000c and keep the heat and therefore turbo spooling energy IN.

Dann

Postby **NitroDann** » Mon May 06, 2013 9:45 pm

Some bits and pieces.

Reproduction rear brace for Earlybird.

Dann

noobee · Postby **noobee** » Mon May 06, 2013 11:31 pm

need a mania one to measure up from?Ken bought me a set for christmas but I only put the front on :wink:

Mick

narita · Postby **narita** » Mon May 06, 2013 11:41 pm

NitroDann wrote:Some bits and pieces.

Reproduction rear brace for Earlybird.

Dann

Those are some beautiful welds.

deviant · Postby **deviant** » Tue May 07, 2013 1:04 am

Down pipe a little close to the AC pipe? Kinda hard to tell on the top down view.

Postby **NitroDann** » Tue May 07, 2013 1:08 am

About an inch of clearance, it should be wrapped or shielded some way.

the manifold design isnt mine, i was asked to build a Greddy manifold for a 1.8L with a T28 so the options for a good 3" downpipe are few and far unfortunately its just a difficult spot to work around and the downpipe took a very long time and as you can see quite a few different welded sections.

Dann