NitroDann's Long Awaited Garage Thread

Postby **NitroDann** » Mon Jun 04, 2012 10:16 pm

I will use a turbo car.

Ill need some measurements.

Dann

bootz · Postby **bootz** » Mon Jun 04, 2012 11:34 pm

I hate to see the waste of a good little car, I bet it was a cracker to drive, police inspected as well.

RIP - But it is great to see you are not crying about it and have plans for moving on with the next one. If this happened to me I would like to think I could suck it up and say to my girlfriend, it's just a car, it can be replaced.

geofiz · Postby **geofiz** » Tue Jun 05, 2012 12:25 am

NitroDann wrote:I will use a turbo car.

Ill need some measurements.

Dann

Let me know what measurement you need, I have the std SE turbo set up etc sitting in my shed, and I ma pretty sure it still has the EGR pipe attached to the exhaust manifold.

Postby **NitroDann** » Tue Jun 05, 2012 12:29 am

If you look back a page you will see a freshly completed turbo manifold, Its for putting a T28 on an SE.

Ill use THAT cars original manifold if need be, but we are hearing that the EGR is in a different spot again.

Im sure Ill need measurements from an N/A NB.

Thanks though geofiz.

Dann

spikes · Postby **spikes** » Tue Jun 05, 2012 1:00 pm

Looks badass, I hope he leaves it that colour, crinkle red would just be wanky and hideous.

Apu · Postby **Apu** » Tue Jun 05, 2012 1:24 pm

If you can wait a week or two, I could make a trip to Newcastle in Apu and hand you my turbo bits...but I'd rather bring the Type R along as I want you to look at doing a few things.

wiztek · Postby **wiztek** » Sat Jun 09, 2012 1:26 am

Jeez, nice car. So much work and effort put in. The best type imo.

deviant · Postby **deviant** » Sat Jun 09, 2012 8:21 pm

Does this help position it?

15mm from the manifold flange to the egr fitting. I guess the angle is dictated by the dipstick tube...4-5mm between egr fitting and dipstick tube.

Postby **NitroDann** » Sat Jun 09, 2012 8:32 pm

Can you please hold a ruler next to it for scale, then Im set, also can someone please post those photos I MMS'd everyone today? :mrgreen:

Dann

deviant · Postby **deviant** » Sat Jun 09, 2012 8:58 pm

Will do...

Only small images but if you click on them they go a bit bigger.

Postby **NitroDann** » Sat Jun 09, 2012 10:13 pm

There it is all mounted. As you can see, its A/C and P/S friendly as well as being very low mount and fully tucked in. Just a couple of millimetres of clearance from turbo to block.

Dann

deviant · Postby **deviant** » Sun Jun 10, 2012 3:19 pm

click through for bigger

itrungs · Postby **itrungs** » Wed Jun 13, 2012 11:16 am

nice meeting you today man, kickass build btw.

Aussie Stig · Postby **Aussie Stig** » Wed Jun 13, 2012 12:49 pm

NitroDann wrote:
There it is all mounted. As you can see, its A/C and P/S friendly as well as being very low mount and fully tucked in. Just a couple of millimetres of clearance from turbo to block.

Dann

That is FREAKIN neat and tidy!