Damn and Blast

Wheels, Suspension, Brakes & Tyres questions and answers

Moderators: timk, Stu, zombie, Andrew, -alex, miata

shake and bake
Driver
Posts: 66
Joined: Thu Sep 17, 2009 12:32 pm
Vehicle: NB8B
Location: Melbourne, Victoria

Damn and Blast

Postby shake and bake » Fri Dec 10, 2010 12:04 pm

After taking the 5 in to get a new thermostat and various other things the mechanic "found" (or in my opinion drove over) a screw which lodged itself into the shoulder of the tyre. After taking it out it was left with an extremely small leak. Im now trying to think of different ways of fixing the leak without having to buy a new tyre ($300-$400). I tried takig down to beaurepairs to see if they could plug it but they cant because its on the shoulder. I bought some tyre sealant from autobarn (the stuff u actually put inside the tyre) but havent tried it yet becuse im not too keen on taking the valve out as it might cause some problems with the seal. Now im considering some super glue on the outside of the tyre. ANY SUGGESTIONS? Has anyone used anything on low profile tubeless tyres that stopped a leak?

User avatar
JBT
Speed Racer
Posts: 7946
Joined: Tue Jun 03, 2003 11:00 am
Vehicle: NC
Location: Brisbane

Re: Damn and Blast

Postby JBT » Fri Dec 10, 2010 12:27 pm

IMHO, if a tyre place won't/can't fix the tyre, you're up for a new tyre. I would not put goop in the tyre for a an attempted permanent fix.
Image

deviant
Racing Driver
Posts: 1717
Joined: Thu Apr 15, 2010 7:23 pm
Vehicle: NB8B
Location: Rockingham - Western Australia

Re: Damn and Blast

Postby deviant » Fri Dec 10, 2010 1:07 pm

Sorry mate but you can not repair a tyre if the hole is on the shoulder or sidewall. Tyre foam / goop is designed to get you directly to a tyre shop at limited speed and nothing more. It is not a permanent fix, even if the tyre could be repaired it has to come off and be cleaned out anyway after you have used goop.

GP
Racing Driver
Posts: 1025
Joined: Tue Nov 21, 2006 10:42 am
Vehicle: ND - 2 GT
Location: Brisbane

Re: Damn and Blast

Postby GP » Fri Dec 10, 2010 1:15 pm

If it was me I would put a plug in it, Used them dozens of times without fail. Wouldn't be doing track days with one in though. I have had 7 plugs in my back tyre of the bike after some mongrel dropped a box of nails on the road and i did 10000k's with them in.
Graham

Sailor
Racing Driver
Posts: 1064
Joined: Wed Jun 24, 2009 5:49 pm
Vehicle: NC
Location: Southie...NOT from " the Shire " :/.

Re: Damn and Blast

Postby Sailor » Fri Dec 10, 2010 1:42 pm

I'd be trying a Dynaplug
http://www.dynaplug.com/
I've used mine a couple of times and very happy.

Not having seen the tyre, the decision is yours BUT it would certainly become a rear tyre.
Rob


05 NCLE, Cosworth SC,PF01,Ohlins,Selby,GWR exh
"We're only given a tiny spark of madness.We mustn't lose it"(Robin Williams)

GP
Racing Driver
Posts: 1025
Joined: Tue Nov 21, 2006 10:42 am
Vehicle: ND - 2 GT
Location: Brisbane

Re: Damn and Blast

Postby GP » Fri Dec 10, 2010 2:08 pm

There's plenty of different brands, They are all similar. Repco have them
Graham

User avatar
Steampunk
Speed Racer
Posts: 4670
Joined: Wed Oct 10, 2007 9:16 am
Vehicle: NA6
Location: Southside of Breeze-bane

Re: Damn and Blast

Postby Steampunk » Fri Dec 10, 2010 6:21 pm

shake and bake wrote:...an extremely small leak....

If you only lose a couple of psi every few days, then just live with it and pump them up regularly. Small inconvenience IMO.

shake and bake wrote:... im not too keen on taking the valve out as it might cause some problems with the seal....?


Huh? what kind of temporary sealant did you buy that instructs you to take the valve out?
In any case, as stated, this is just a temporary/emergence measure as it will mess up your balance/steering.
Image

User avatar
Entice
Fast Driver
Posts: 145
Joined: Tue Jun 17, 2003 11:00 am
Vehicle: NA6
Location: Melbourne
Contact:

Re: Damn and Blast

Postby Entice » Sat Dec 11, 2010 6:42 am

Let me get this straight...

You are prepared to have a substandard MAJOR safety component on your car for the sake of a few hundred bucks?
More opportunities have been lost from indecision, rather than wrong decision.

User avatar
de Bounce
Racing Driver
Posts: 1091
Joined: Thu Feb 12, 2009 5:19 pm
Vehicle: NC
Location: Northern Burbs - Melbourne

Re: Damn and Blast

Postby de Bounce » Sun Dec 12, 2010 5:07 am

shake and bake wrote:... im not too keen on taking the valve out as it might cause some problems with the seal....?
Have a read of the instructions again.
It should be as simple as:
remove valve core
insert goop
reinsert valve core
re-inflate tyre

The valve core is not the rubber bit but the metal bit inside
There are some tyre sealants which can be inserted and will remain a liquid until required.
Something like THIS
Still wouldn't trust it especially with the hole in the shoulder of the tyre.
2011 NC2 PRHT SE in Dolphin Grey
2001 NB8B in Crystal Blue - Sold :(
Motorkhana Video

GP
Racing Driver
Posts: 1025
Joined: Tue Nov 21, 2006 10:42 am
Vehicle: ND - 2 GT
Location: Brisbane

Re: Damn and Blast

Postby GP » Mon Dec 13, 2010 1:18 pm

I've never had any luck with the liquids but know of several people who run it in their motorbike tyres from new and claim it seals leaks instantly. You only get what you pay for however
You are prepared to have a substandard MAJOR safety component on your car for the sake of a few hundred bucks?

:?:
Graham

deviant
Racing Driver
Posts: 1717
Joined: Thu Apr 15, 2010 7:23 pm
Vehicle: NB8B
Location: Rockingham - Western Australia

Re: Damn and Blast

Postby deviant » Mon Dec 13, 2010 2:58 pm

GP wrote:I've never had any luck with the liquids but know of several people who run it in their motorbike tyres from new and claim it seals leaks instantly. You only get what you pay for however
You are prepared to have a substandard MAJOR safety component on your car for the sake of a few hundred bucks?

:?:


The ONLY thing keeping your car on the road are the 4 contact patches about as big as your hand that your tyres have.

To compromise this is foolish at best. Having cheap, old, leaking or poorly repaired tyres is just asking for trouble.

GP
Racing Driver
Posts: 1025
Joined: Tue Nov 21, 2006 10:42 am
Vehicle: ND - 2 GT
Location: Brisbane

Re: Damn and Blast

Postby GP » Tue Dec 14, 2010 10:49 am

Whatever, The worst that can happen is the tyre might go flat again. :D
Graham

SPy vs. SPy
Racing Driver
Posts: 902
Joined: Wed Mar 10, 2004 7:40 pm
Vehicle: ND - 2
Location: In a fast car, so not an NC.

Re: Damn and Blast

Postby SPy vs. SPy » Tue Dec 14, 2010 1:41 pm

GP wrote:Whatever, The worst that can happen is the tyre might go flat again. :D


One would think the worst thing that can happen is the tyre can fail at highway speeds :shock: :| :(

Quoting the Mastercard ad
new tyre $350
your life . . . priceless

All that being said, even with a repaired tyre he'll probably still be out on the roads with cars in a much worse state of safety with "safe drivers" :shock: driving each one of them.
Went for a drive and there were slow cars everywhere, why are NC's so common . . . must be NC = Normally Cardiganed.


Return to “MX5 Wheels, Suspension, Brakes & Tyres”

Who is online

Users browsing this forum: No registered users and 233 guests