Just a quick question. Does anyone have the tool for holding the crank while undoing the big nut (simialr to the tool in the service manual) Any chance i could borrow for a week?
if not is there any secrets as to getting the nut off?
Cheers
Quick timing belt question
Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy
-
Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Quick timing belt question
I shall be attempting a timing belt change on my car next week. Done them before on mates cars, so hopefully all will go well.
Just a quick question. Does anyone have the tool for holding the crank while undoing the big nut (simialr to the tool in the service manual) Any chance i could borrow for a week?
if not is there any secrets as to getting the nut off?
Cheers
Just a quick question. Does anyone have the tool for holding the crank while undoing the big nut (simialr to the tool in the service manual) Any chance i could borrow for a week?
if not is there any secrets as to getting the nut off?
Cheers
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
Juffa
- Racing Driver
- Posts: 1751
- Joined: Sun Apr 27, 2003 11:00 am
- Vehicle: ND - 2 GT
- Location: Bayside - Melbourne
- Contact:
Quick timing belt question
I found that by putting the car into gear, 5th I believe, then I could undo the nut. Just make sure the rear wheels are on the ground, hand brake is applied and the wheels are chocked so the car can't move. I used a large pry bar over the socket wrench to give me the leverage.
Have you worked out how to stop the cams moving when changing the belt?
J.
Have you worked out how to stop the cams moving when changing the belt?
J.
Last edited by Juffa on Wed May 26, 2010 3:04 pm, edited 1 time in total.
Former owner of Mailbu Stacey, Smurfette and Tweety.
-
fattima
- Racing Driver
- Posts: 602
- Joined: Thu Aug 23, 2007 5:49 am
- Vehicle: ND - 2 GT
- Location: Melbourne
Quick timing belt question
Both times I've done a cambelt change I did as Juffa mentions, no problems. One I didn't need an extension the bolt just unwound with very little force 
-
wun911
- Speed Racer
- Posts: 2114
- Joined: Tue Sep 11, 2007 12:13 pm
- Vehicle: ND - 2 GT
- Location: Melbourne
Quick timing belt question
flyin miata sells the tool you want its like 30 bucks someone should buy it and cut out a template...
every ounce counts
-
Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Quick timing belt question
Juffa wrote:I found that by putting the car into gear, 5th I believe, then I could undo the nut. Just make sure the rear wheels are on the ground, hand brake is applied and the wheels are chocked so the car can't move. I used a large pry bar over the socket wrench to give me the leverage.
Have you worked out how to stop the cams moving when changing the belt?
J.
ahh didnt think of that...it should do the job then
as for the cams moving...nup i got a week to think about it
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
fattima
- Racing Driver
- Posts: 602
- Joined: Thu Aug 23, 2007 5:49 am
- Vehicle: ND - 2 GT
- Location: Melbourne
-
Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Quick timing belt question
looks good enough for me!
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
StanTheMan
- Forum legend
- Posts: 6824
- Joined: Thu Apr 24, 2003 11:00 am
- Vehicle: NA6
- Location: Balgowlah
Quick timing belt question
each to thier own. Whatever works for you.
But I found TDC on No 1
line up the marks works a treat.
Unfortunately with your NB8B you don't have the luxury of the marks you have with the non VVT models
&
But frankly I'd personally check the markings & final check with counting teeth. Maybe even mark the cam sprockets on the intake side.
But I found TDC on No 1
line up the marks works a treat.
Unfortunately with your NB8B you don't have the luxury of the marks you have with the non VVT models
&
But frankly I'd personally check the markings & final check with counting teeth. Maybe even mark the cam sprockets on the intake side.
Satans Ride called F33nix the resurrected NA6
Return to “MX5 Engines, Transmission & Final Drive”
Who is online
Users browsing this forum: No registered users and 121 guests
