Finally got round to making my heatshield to go over the extractors. Hopefully it will lower the temps under the bonnet. I'll put up another pic when it goes on the car.
I used a sheet of this stuff to make it: http://www.aclperformance.com.au/prod_heatshield.htm
Heatshield
Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy
-
rossint
- Fast Driver
- Posts: 460
- Joined: Wed Jan 09, 2008 7:56 pm
- Vehicle: NA6
- Location: ADELAIDE
Heatshield
You do not have the required permissions to view the files attached to this post.
-
Steampunk
- Speed Racer
- Posts: 4670
- Joined: Wed Oct 10, 2007 9:16 am
- Vehicle: NA6
- Location: Southside of Breeze-bane
Heatshield
looks good 
great product; cheap, easy to form, light but strong, works.
You can touch it after only a few minutes after a spirited drive.
great product; cheap, easy to form, light but strong, works.
You can touch it after only a few minutes after a spirited drive.
-
93_Clubman
- Speed Racer
- Posts: 11857
- Joined: Mon Aug 08, 2005 11:35 pm
- Vehicle: Clubman
- Location: Melbourne
Heatshield
nice - tks for sharing
-
TieNN89
- Speed Racer
- Posts: 2012
- Joined: Mon Nov 26, 2007 8:27 pm
- Vehicle: NC
- Location: Brisbane
- Contact:
-
broady
- Racing Driver
- Posts: 1243
- Joined: Fri Jan 19, 2007 12:32 am
- Vehicle: NA8
- Location: Sydney NSW
Heatshield
Ross, where'd you get the stuff? Supercheap? And how much did it cost?
人馬一体 NA8
Tein SS, Torsen T2, BD, Maxim Works→RS*R, ARC, Koyo, SSR, Sparco, Flyin' Miata & bling!
6/5/2010
-
rossint
- Fast Driver
- Posts: 460
- Joined: Wed Jan 09, 2008 7:56 pm
- Vehicle: NA6
- Location: ADELAIDE
Heatshield
I got it from Supercheap, $50. I used just over half the sheet but you could get 2 out of a sheet if you made it a tad smaller.
It will be bolted onto the 2 existing holes just under the cam cover at the front of the motor, I hope it doesn't vibrate around too much.
I won't have any pics until I get back in about a week or so.
It will be bolted onto the 2 existing holes just under the cam cover at the front of the motor, I hope it doesn't vibrate around too much.
I won't have any pics until I get back in about a week or so.
-
broady
- Racing Driver
- Posts: 1243
- Joined: Fri Jan 19, 2007 12:32 am
- Vehicle: NA8
- Location: Sydney NSW
Heatshield
Went to Stoopercheap today to get some, they didn't have it 
人馬一体 NA8
Tein SS, Torsen T2, BD, Maxim Works→RS*R, ARC, Koyo, SSR, Sparco, Flyin' Miata & bling!
6/5/2010
-
Mr Morlock
- Speed Racer
- Posts: 6444
- Joined: Mon Feb 04, 2008 11:40 am
- Vehicle: NB8B
- Location: Melbourne
Heatshield
Repco are their distributors. Check the web site.
-
Steampunk
- Speed Racer
- Posts: 4670
- Joined: Wed Oct 10, 2007 9:16 am
- Vehicle: NA6
- Location: Southside of Breeze-bane
-
wun911
- Speed Racer
- Posts: 2114
- Joined: Tue Sep 11, 2007 12:13 pm
- Vehicle: ND - 2 GT
- Location: Melbourne
Heatshield
looks like tin foil should be lite...
you guys think its worth covering the extractor heat shield with it??
you guys think its worth covering the extractor heat shield with it??
every ounce counts
-
Uncle Arthur
- Dodgy Award Benefactor
- Posts: 1802
- Joined: Wed Apr 23, 2003 11:00 am
- Vehicle: ND - 2 GT
- Location: Doesn't matter where I'm from-it's that your daughter is with me that's the biggest concern :D
- Contact:
Heatshield
I use the same stuff as the heat shield for my turbo and dump pipe. I haven't had any hoses or plastic melt on the cold side of the shield yet, so perhaps it works afterall..... 
Founder of the QLD Chapter of the Honourable Brothers of Dodgy.
Benefactor of the Perpetual Dodgy award - Inaugural year 2007.
Benefactor of the Perpetual Dodgy award - Inaugural year 2007.
-
Locutus
- Racing Driver
- Posts: 879
- Joined: Thu Jul 26, 2007 7:39 pm
- Vehicle: NB SP
- Location: Sydney
- Contact:
Heatshield
wun911 wrote:you guys think its worth covering the extractor heat shield with it??
If you mean the factory heat shield, nope.
-
bruce
- Speed Racer
- Posts: 7708
- Joined: Fri Apr 25, 2003 11:00 am
- Vehicle: NA8 - Turbo
- Location: Victoria
- Contact:
Heatshield
Regards Repco, shop around between the Repco stores as some of their prices vary markedly (eg. one store quoted $180 for a muffler, the second store $250!)
-
rossint
- Fast Driver
- Posts: 460
- Joined: Wed Jan 09, 2008 7:56 pm
- Vehicle: NA6
- Location: ADELAIDE
Heatshield
Installed...
You do not have the required permissions to view the files attached to this post.
-
Hammer
- Speed Racer
- Posts: 2849
- Joined: Fri Apr 25, 2003 11:00 am
- Vehicle: NB SP
- Location: Sydney
- Contact:
Return to “MX5 Engines, Transmission & Final Drive”
Who is online
Users browsing this forum: No registered users and 207 guests
