good afternoon.
i bought one of these style bars from MX mania today. There is any pointers on installing the bar? from the looks of it, it needs some cutting of the plastic trim to make it fit.
Any pointers would be tops
Cheers
OBX style Bar
Moderators: timk, Stu, zombie, Andrew, -alex, miata
- Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
OBX style Bar
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
- Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
Re: OBX style Bar
anything? or should i write up something when i get around to doing it
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
-
- Speed Racer
- Posts: 6444
- Joined: Mon Feb 04, 2008 11:40 am
- Vehicle: NB8B
- Location: Melbourne
OBX style Bar
Regie an earlier post was lost in the transition. If you bought the product from Mania I would expect that they would have advice available on installation.
- Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
OBX style Bar
cheers mate im going to attack it tomorrow!
horay for good weather
horay for good weather
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
- Regie
- Speed Racer
- Posts: 4259
- Joined: Thu May 15, 2008 3:02 pm
- Vehicle: NC - V8
- Location: Sydney
OBX style Bar
ok its installed and wow the rear end feels sooo much more stiffer. goes round corners like its got glue on the tyres. definate handling improvement! ill post up pics later!
MY07 NC, Mazdaspeed Body, Ohlins, Full GWR Exhaust, 17x9 RPF1's, 4.1FGR and lots lots more
OBX style Bar
Regie wrote:ok its installed and wow the rear end feels sooo much more stiffer. goes round corners like its got glue on the tyres. definate handling improvement! ill post up pics later!
know its been a while .. but pics please:)
I've just thought about getting one of these..
Was it hard to DIY?
OBX style Bar
Are there any know issues with roof clearance for the OBX or similar syle bars in an NA6
- sliq
- Speed Racer
- Posts: 3414
- Joined: Sat Jan 13, 2007 12:33 am
- Vehicle: ND - 2 GT
- Location: Sydney
- Contact:
OBX style Bar
li21 wrote:Are there any know issues with roof clearance for the OBX or similar syle bars in an NA6
i don't think they should, since they sit not much higher than the na seats.. and the na seats are fairly low imo compared to nb8b ones.
i can't brain today.. i have the dumb..
OBX style Bar
sliq wrote:li21 wrote:Are there any know issues with roof clearance for the OBX or similar syle bars in an NA6
i don't think they should, since they sit not much higher than the na seats.. and the na seats are fairly low imo compared to nb8b ones.
Hmm.. the pictures ive seen show they sit quite a bit above the NA seats and only just above NB seats?
Just heard that they are a tight fit on the early hoods.. Guess ill call Mania tomorrow and check
Return to “MX5 Body, Paint, Interior & Trim”
Who is online
Users browsing this forum: No registered users and 36 guests