Aftermarket Exhaust

[TieNN89]

Alright so i finished work early today

went to Right Price Exhaust today and asked about the exhaust etc

They made up a quote for me

Extractors I'm pretty sure Hurricane
X Force Cat Back
High Flow Cat

$1562 Fitted

I asked how big the tubing was and apparently its 2\"

[TieNN89]

I don't know Gary Stewarts' number (I thought I had it), but Novice1 (Ron) does, send him a PM.

The "Loch Stewart" headers are made by CES Racing by the way, down Beenleigh way. From what I gather, custom exhausts don't get much better, so if you can use up to $2000 may as well go there. I would.

mm They're not that far might give them a call tomorrow if they are open

[Boags]

Extractors I'm pretty sure Hurricane
X Force Cat Back
High Flow Cat

$1562 Fitted

I asked how big the tubing was and apparently its 2"

Do they say thank-you after you let them rape you?

Walk away.

[TieNN89]

Extractors I'm pretty sure Hurricane
X Force Cat Back
High Flow Cat

$1562 Fitted

I asked how big the tubing was and apparently its 2"

Do they say thank-you after you let them rape you?

Walk away.

roflmao

btw it was a $1000 somehow it has turned into $1500





so confused

[MINX]

I just used 'Right Price' to put in my Magnaflow High Flow Cat.
Mainly because they were convenient. $320.
They are not very customer friendly, but hey, got the job done.
The actual fitter was good, just counter staff were disinterested.

Anyway - OMG!
What a big difference it made.
I already had cat back done 2.5\". no resonator.
More response now, and upper end power. Noticeable change.
And the sound! As Rexxy would say \"Magnificent!\"
The std cat was definitely holding it back.

[GP14]

I don't know Gary Stewarts' number (I thought I had it), but Novice1 (Ron) does, send him a PM.

Gary Stewarts number 32733164.

1500? tell 'em their dreaming.

I have the 'Loch Stewart' setup 2 1/4 inch cat back from Rob Bliss. No droning. sweet sound.

does he own a performance shop or something?

PM sent to Novice1

He works from home but he builds mx5 race cars so I figure he knows a thing or 2 about what setup you would need. Give him a call.

[16bit]

I don't know Gary Stewarts' number (I thought I had it), but Novice1 (Ron) does, send him a PM.

Gary Stewarts number 32733164.

1500? tell 'em their dreaming.

I have the 'Loch Stewart' setup 2 1/4 inch cat back from Rob Bliss. No droning. sweet sound.

does he own a performance shop or something?

PM sent to Novice1

He works from home but he builds mx5 race cars so I figure he knows a thing or 2 about what setup you would need. Give him a call.

werd

[Mokesta]

My system with X-Force headers, N*Power cat and N*Power rear with 2.25\" tube will come out to be about $1000 total. Could have been about $300 less if we didn't use expensive laser cut 8mm 3-bolt flanges and the X-Force headers. The no name headers I also have are very nearly as good.

See my rides section for photos.

M

[TieNN89]

Well I'll be going to Exotic Exhaust

When i went to Price Right the way they spoke to me was just $h1t and no way I'll be leaving my car there


So I'm gona take her to Exotics Exhaust possible tomorrow or the next day
Just waiting to get her back and get approval from insurance and its all good :biggrin:

[tuned_to_fly]

Tien - I also have the Lock Stewart cat back exhaust and it sounds and goes really well. Rob Bliss who are known for awesome work do the system and I was in there today and they are very helpful. Worth a try I'd say!

[orx626]

Could have been about $300 less if we didn't use expensive laser cut 8mm 3-bolt flanges and the X-Force headers.
M

Not sure that they would have been more than $2-3 cheaper per flange plate if done in 6mm......at least with laser we didn't have to drill the bolt holes out

[TieNN89]

Tien - I also have the Lock Stewart cat back exhaust and it sounds and goes really well. Rob Bliss who are known for awesome work do the system and I was in there today and they are very helpful. Worth a try I'd say!

Well everythings all set now so i can't change anything unless maybe its still under that quoted price

and it will have to be done at Exotics Exhaust

cause insurance has as far as i know approved it and there gona have a chat tomorrow as to how its gona get paid etc

[oongie]

So, how would I \"a Sydney sider\" get my hands on a loch-stewart zorst system apart from going up to brisvegas?

Cheers Paul

[Mokesta]

Could have been about $300 less if we didn't use expensive laser cut 8mm 3-bolt flanges and the X-Force headers.
M

Not sure that they would have been more than $2-3 cheaper per flange plate if done in 6mm......at least with laser we didn't have to drill the bolt holes out

Hey! Get off the net and back to selling stuff to cashed-up coal miners!! You think you're in Mackay for a holiday!! What I meant was that with 2 bolt flanges I would have needed 2 less and they would have been cheaper.

[orx626]

Could have been about $300 less if we didn't use expensive laser cut 8mm 3-bolt flanges and the X-Force headers.
M

Not sure that they would have been more than $2-3 cheaper per flange plate if done in 6mm......at least with laser we didn't have to drill the bolt holes out

Hey! Get off the net and back to selling stuff to cashed-up coal miners!! You think you're in Mackay for a holiday!! What I meant was that with 2 bolt flanges I would have needed 2 less and they would have been cheaper.

It's f#ck'n p1$$ing down rain since yesterday afternoon...and all night...and its still pouring hard! Can't see too many people venturing out today.

Can't control mother nature....except for global warming so they say....

Ok back on topic......