GROUP BUY - Number Plate Bracket: Front or Side Mount NA/NB

Body, Paint, Interior and Trim questions and answers

Moderators: timk, Stu, zombie, Andrew, -alex, miata

Post Reply
User avatar
Ajay
Racing Driver
Posts: 901
Joined: Mon Dec 11, 2006 6:07 pm
Vehicle: NA6
Location: Western Sydney, NSW
Contact:
Contact Ajay

Postby Ajay » Mon Nov 19, 2007 11:11 pm

yep that'll do it!.. after reading your post i looked at my car and figured out what you had done :)

unfortunalty i didnt keep the ones off my wreck.. ring mania.. you only need the right one.. and it doesnt look dumb as you cant see the hook anyways :)
Image
Top
Dodgy Haro

Re:

Postby Dodgy Haro » Wed Nov 21, 2007 1:23 pm

TP13SS wrote:hey raymo!..

mine cleared the bumper with HEAPS of room.. did you pull it as far forward as you could when you were doing up the bolt on the tow hook?

Cheers
Ajay


Hmmm ... there weren't any instructions so I just used the bolt + washer ring to secure the license bracket to the tow hook ... is there any secret apart from just tightening it enough so it is secure?

Image
Image
Top
User avatar
kenson
Fast Driver
Posts: 268
Joined: Fri Oct 19, 2007 10:55 pm
Vehicle: NB SE
Location: Perth

Postby kenson » Mon Nov 26, 2007 9:28 am

I had my car reversed into and the protruding screws wrecked my untouched front bar :cry:

This bracket looks like it would solve some problems and looks good too. What number plate sizes fits the bracket? Sorry if this has already been answered!

I scrolled through the thread quickly. It looks likes a lot of you have personalised smaller plates. I just have the normal sized WA plates

Cheers,

Ken
Top
User avatar
Jimmy
Fast Driver
Posts: 451
Joined: Tue Mar 20, 2007 7:19 pm
Vehicle: ND - 2 GT
Location: Canberra

Postby Jimmy » Mon Nov 26, 2007 11:23 am

What number plate sizes fits the bracket?


If your going for personalised plates then order them without holes. It means that u drill them exactly where you want them to be and you dont end up with holes which arent used.
Image
Top
User avatar
Boags
Speed Racer
Posts: 3533
Joined: Thu Nov 10, 2005 6:25 pm
Vehicle: NB SP
Location: Brisvegas
Contact:
Contact Boags

Re:

Postby Boags » Mon Nov 26, 2007 8:06 pm

JimmyJ5 wrote:
What number plate sizes fits the bracket?


If your going for personalised plates then order them without holes. It means that u drill them exactly where you want them to be and you dont end up with holes which arent used.


ALL plates should have holes in the same place to comply with ADRs. Richard has MOST CERTAINLY designed these to comply with the ADRs. ALL plates fit. :D

Cheers,

Boags
Spartan Motor Sport : http://www.SpartanMS.com.au
Top
Rob E
Fast Driver
Posts: 485
Joined: Wed Apr 23, 2003 11:00 am
Vehicle: ND - 2 GT
Location: Sydney
Contact:
Contact Rob E

Postby Rob E » Tue Dec 11, 2007 7:14 pm

Gday All,

I have a Boags special side mount stay sitting here gathering dust. You too can be the epitomy of JDM cool.

Just bring a 6 pack of Asahi Super dry and its yours. Sydney collection (Sutherland Shire) PM me.
Top
User avatar
marcusus
Speed Racer
Posts: 2919
Joined: Thu Jul 13, 2006 12:07 am
Vehicle: NB8A

Postby marcusus » Tue Dec 11, 2007 8:50 pm

I'm a bit late to the party, but you can see a shot of mine here. Yes I know it's wonky. I need to adjust that :P

Incidentally, is that spot about how high everybody else's sit? I swear it looks like it's lower than everyone elses...
Top
Post Reply

Return to “MX5 Body, Paint, Interior & Trim”

Who is online

Users browsing this forum: No registered users and 91 guests