Page 1 of 1
Jerrah's COPs build.
Posted: Fri Jul 15, 2011 11:33 am
by jerrah
I know it's been done before and it will be done again but I thought I'd document the build up of my COP setup.
I've already purchased my new Toyota COPx4 from ebay and have just received my J702T ignitor which I'm using to make the setup plug and play. Time permitting I hope to have it finished by next week and I'll post pictures as I work.
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 11:45 am
by NitroDann
As you would know I plan on building these and selling them for cost price. Have you found a good cheap source of coils, or did you pay 80 buxks each at a wreckers like everyone else?
Dann
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 11:51 am
by jerrah
I paid about $120 for four new in box including connectors. The seller doesn't have any currently for sale but I could enquire if he will sell more?
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 11:54 am
by jerrah
I've already fixed that through tuning and fixing a noisy signal but it will surely help.
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 12:02 pm
by NitroDann
Geez 120? What brand? ask him how much for 20 with pigtails please.
This will fix and spark issues. See page 5 in my thread, they can throw a 60mm long spark if you want. Ive got a pic of a very strong consistant 40mm spark on page 5. And of course with cops youll have 4 of these beauties.
It made such a big difference to my car, pushing spark through high compresion E85 and asking 2 coils to dwell at 8500rpm wasnt good.
Dann
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 12:14 pm
by jerrah
This seller on ebay has two sets for sale atm $135
http://www.ebay.com.au/itm/COP-Ignition-Coils-Kit-4AGE-Toyota-Corolla-Echo-Yaris-/140576312911?pt=AU_Car_Parts_Accessories&hash=item20bb004e4fGeneric but new coils. More fool me if they don't work I guess...
The kit consists of...
4 x CoP Ignition Coils
4 x matching connectors for the coils
20 x connector terminals
20 x connector wire seals
The coils used in this kit match Toyota P/N 90919-02239 and are found on the 1ZZ-FE engine.
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 12:38 pm
by jerrah
I just prised off the bottom plate on the ignitor. Seems to be filled with a sticky silicon, I imagine I'll need to desolder the board from the pins.
Re: Jerrah's COPs build.
Posted: Fri Jul 15, 2011 12:56 pm
by NitroDann
MUCH easier just to cut them off. And clean that gunk out thouroughly or youll have a LOT of difficulty soldering. Careful its all very fragile in there, your soldering to praactically aluminium foil.
Dann
noob Q
Posted: Sun Jul 17, 2011 4:35 am
by slimx
what is a "cop setup"?
Jerrah's COPs build.
Posted: Sun Jul 17, 2011 9:45 am
by gslender
Coil over plug. Idea is that more boogie is delivered when coil discharges directly into plug, avoiding leads etc.
Re: Jerrah's COPs build.
Posted: Sun Jul 17, 2011 9:49 am
by NitroDann
^
I like your style.
Going to coil over plug you go from 2 coils and a set of leads, to 4 much more powerful coils attached directly to the spark plug.
View'nitrodanns long awaited garage thread' pages 1/2/3 and maybe 4(?) for a lot more detail discussion and photos.
Dann
Re: Jerrah's COPs build.
Posted: Mon Jul 18, 2011 9:27 am
by jerrah
Had a busy weekend, didn't get anything done on the wiring loom but installed a LED and reset switch for LC1's in two cars.
Re: Jerrah's COPs build.
Posted: Sat Aug 06, 2011 11:57 am
by rxmx
Ive done this conversion, make sure you clean those contacts throroughly that gunk is a bastard to get off. I used cotton bud with some wax/grease remover then soldered and used heat shrink, hasnt failed in over 6 months