Hi,
Can I get some input on machining the disk rotors?
Is it necessary to machine everytime the pads are replaced?
Or this should only be done if the surface of the rotors are uneven?
Also, are rotors on mxs can be machined?
cheers
yem11n
Disk rotor machining
Moderators: timk, Stu, zombie, Andrew, -alex, miata
-
yem11n
- Fast Driver
- Posts: 258
- Joined: Mon Aug 01, 2011 4:24 pm
- Vehicle: NB SE
- Location: Sydney
Disk rotor machining
Darkness BLACK 130i (2006) Sold
Tiny BLACK SE (2005)
A few mods.
BLACK CX5 Akera 2015
Stock as.
Tiny BLACK SE (2005)
A few mods.
BLACK CX5 Akera 2015
Stock as.
-
NitroDann
- Forum sponsor
- Posts: 10280
- Joined: Thu Nov 05, 2009 12:10 pm
- Vehicle: NA6
- Location: Newcastle NSW
- Contact:
Re: Disk rotor machining
MX5s can be machined, only if there is a significant lip on the disk edge, or they are not straight.
Dann
Dann
http://www.NitroDann.com
speed wrote:If I was to do it again, I wouldn't even consider the supercharger.
-
Steampunk
- Speed Racer
- Posts: 4670
- Joined: Wed Oct 10, 2007 9:16 am
- Vehicle: NA6
- Location: Southside of Breeze-bane
-
Guran
- Speed Racer
- Posts: 3754
- Joined: Sun Feb 15, 2009 6:42 pm
- Vehicle: ND - 1.5
- Location: Albion Park NSW
- Contact:
Re: Disk rotor machining
I've had a set of NA6 rotors machined after they developed a bit of a shudder. Cost was $50 for the front set from my local brake specialist. It's not necessary to machine them with each pad change. I've been getting a few pad changes without touching the rotors. If you get them machined, tou need to check their thickness with a micrometer and make sure they're not below the minimum thickness. A new set of front rotors should only cost around $100.
Standard 2006 NC - YouTube
WP 1:11.89 | SMP-S 1:05.90 GP 1:54.93 N 1:18.09 L 2:22.49 | PW 1:02.52
PI 2:00.55 | W-S 1:12.44 W-L 1:43.36 | SR 1:33.25
WP 1:11.89 | SMP-S 1:05.90 GP 1:54.93 N 1:18.09 L 2:22.49 | PW 1:02.52
PI 2:00.55 | W-S 1:12.44 W-L 1:43.36 | SR 1:33.25
-
yem11n
- Fast Driver
- Posts: 258
- Joined: Mon Aug 01, 2011 4:24 pm
- Vehicle: NB SE
- Location: Sydney
Re: Disk rotor machining
thanks for the info fellas.. 
yem11n
yem11n
Darkness BLACK 130i (2006) Sold
Tiny BLACK SE (2005)
A few mods.
BLACK CX5 Akera 2015
Stock as.
Tiny BLACK SE (2005)
A few mods.
BLACK CX5 Akera 2015
Stock as.
-
Dweezle
- Racing Driver
- Posts: 1923
- Joined: Wed Mar 12, 2008 8:51 am
- Vehicle: NA6
- Location: Sydney
Re: Disk rotor machining
If your in Sydney, brookers brakes do RDA rotors for under $30 each last time i got a set.
Much better than machining.
Much better than machining.
ALL MUSCLE CARS ARE CRAP
Jeremy Clarkson
except of course, the Almighty VIPER!!!!
Jeremy Clarkson
except of course, the Almighty VIPER!!!!
-
Guran
- Speed Racer
- Posts: 3754
- Joined: Sun Feb 15, 2009 6:42 pm
- Vehicle: ND - 1.5
- Location: Albion Park NSW
- Contact:
Re: Disk rotor machining
Dweezle wrote:If your in Sydney, brookers brakes do RDA rotors for under $30 each last time i got a set.
Much better than machining.
Holy cow! That's cheap! I got my DBAs from Supercheap for $100 a set (front pair).
Standard 2006 NC - YouTube
WP 1:11.89 | SMP-S 1:05.90 GP 1:54.93 N 1:18.09 L 2:22.49 | PW 1:02.52
PI 2:00.55 | W-S 1:12.44 W-L 1:43.36 | SR 1:33.25
WP 1:11.89 | SMP-S 1:05.90 GP 1:54.93 N 1:18.09 L 2:22.49 | PW 1:02.52
PI 2:00.55 | W-S 1:12.44 W-L 1:43.36 | SR 1:33.25
-
Hellmun
- Racing Driver
- Posts: 979
- Joined: Sat Feb 10, 2007 1:15 pm
- Vehicle: NB8B - Turbo
- Location: Wollongong,NSW
Re: Disk rotor machining
You can get DBA street front rotors for $60 odd from n*power and probably other places (check forum sponors?)... machining isn't much less than that. If your changing pad type it can sometimes be highly recommended to machine/replace rotors. E.g changing between a metallic, asbestos or ceramic type. EBC's pads actually come with an abrasive cleaning surface on their pads to improve bed-in.
Return to “MX5 Wheels, Suspension, Brakes & Tyres”
Who is online
Users browsing this forum: No registered users and 164 guests
