B6 Bogging 2k-4k - Closed throttle > WOT

Engines, Transmissions & Final Drive questions and answers

Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy

Skyntara
Driver
Posts: 90
Joined: Thu Nov 17, 2011 10:57 pm

B6 Bogging 2k-4k - Closed throttle > WOT

Postby Skyntara » Wed Jan 08, 2014 3:36 pm

Hi Guys,

Funny problem that I've had for quite a while. I usually just drive around it (more throttle), but it's a bit of a pain sometimes.

Car runs great, revs out, plenty of power.

Often when I'm cruising along in gear with little or no throttle and then give it a bit of a squirt, the car hesitates before taking off. Between 2k and 4k RPM. Above that, no issues. If i take off from idle and run up through the gears it doesn't happen at all.

Have a JR CAI and Xforce extractors. Happened to a similar extent on stock intake and exhaust. Plugs are new, leads are new.

Should I be investigating coils/igniter? I can probably borrow some for testing. Anything else I should be looking at?

Cheers

User avatar
MrRevhead
Racing Driver
Posts: 715
Joined: Mon Mar 26, 2012 2:40 pm
Vehicle: NA6
Location: NW Sydney

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby MrRevhead » Wed Jan 08, 2014 5:42 pm

Cleaned the flapper on the AFM or throttle body butterfly recently?

No leaks around the intake? (clamps on tight, rubber joiners in good condition etc)
1991 NA6 BRG Limited Edition #124 (Aus Delivered)
Image

Skyntara
Driver
Posts: 90
Joined: Thu Nov 17, 2011 10:57 pm

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby Skyntara » Wed Jan 08, 2014 6:30 pm

clamps and joiners are fine.

I guess I'll give the afm flapper and butterfly a clean with carby cleaner. Since I don't own a car with a carb any more I might as well use it for something.

cookie
Fast Driver
Posts: 471
Joined: Thu Dec 19, 2013 10:36 pm
Vehicle: NA6

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby cookie » Wed Jan 08, 2014 6:38 pm

Skyntara wrote:clamps and joiners are fine.

I guess I'll give the afm flapper and butterfly a clean with carby cleaner. Since I don't own a car with a carb any more I might as well use it for something.



Not sure if it applies here but hotwires don't like car by cleaner. There's electronic's safe stuff which I've used successfully (contact cleaner).

ralt
Fast Driver
Posts: 423
Joined: Thu May 19, 2011 11:10 am
Vehicle: ND - 2
Location: brisbane

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby ralt » Wed Jan 08, 2014 6:41 pm

Hi.
I will try again.
Do not use carby cleaner on the butterfly it will remove the sealer. Use only throttle body cleaner,

Skyntara
Driver
Posts: 90
Joined: Thu Nov 17, 2011 10:57 pm

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby Skyntara » Thu Jan 09, 2014 5:02 am

Guess I'm stuck with the carby cleaner a bit longer then.

Off to get some throttle body cleaner

project.r.racing
Speed Racer
Posts: 3722
Joined: Sun Jan 18, 2009 10:16 pm
Vehicle: Non MX-5
Location: Glasshouse Mountains, QLD

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby project.r.racing » Thu Jan 09, 2014 1:34 pm

check the leads and coils aren't earthing out before the spark gets to the plugs.

93_Clubman
Speed Racer
Posts: 11854
Joined: Mon Aug 08, 2005 11:35 pm
Vehicle: Clubman
Location: Melbourne

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby 93_Clubman » Fri Jan 10, 2014 11:08 am

Washed the motor lately or has water got into the upper engine bay? See Droo's post in following:
viewtopic.php?f=55&t=57190&p=720469&hilit=na%2A+hesitat%2A+accelerat%2A#p720469

Skyntara
Driver
Posts: 90
Joined: Thu Nov 17, 2011 10:57 pm

Re: B6 Bogging 2k-4k - Closed throttle > WOT

Postby Skyntara » Sun Jan 12, 2014 1:03 am

Motor is very dry.

Never wash the outside of the car, let alone the engine bay.


Return to “MX5 Engines, Transmission & Final Drive”

Who is online

Users browsing this forum: No registered users and 80 guests