Stalling once warmed up

Engines, Transmissions & Final Drive questions and answers

Moderators: timk, Stu, zombie, Andrew, The American, Lokiel, -alex, miata, StanTheMan, greenMachine, ManiacLachy, Daffy

User avatar
angusis2fast4u
Fast Driver
Posts: 313
Joined: Mon Jul 01, 2013 10:48 pm
Vehicle: NB8B
Location: Western Suburbs, Brisbane

Stalling once warmed up

Postby angusis2fast4u » Mon Sep 02, 2013 10:54 pm

So as the title suggest my mx seems to stall when the clutch is in, usually is most common when slowing down at the lights. it only really happens once the car is warmed up, i've heard it might be something to do with the choke and raising a float when the water heats up in the vein airflow meter? and while we're fixing something should i upgrade? i hear people put RX-7 airflow meters in MX-5's to make them more efficient? would that be the way to go or just pick up a replacement to see if it's good? or clean it out?

also a ticking noise directly related to the speed of the engine.. is that something to worry about? the car has rarely been used until about a month ago, since then has been used "spiritedly" to say it in a nice way..
~Angus
2001 Silver NB8B
Past: Grey 1990 Eunos Roadster

User avatar
NitroDann
Forum sponsor
Posts: 10280
Joined: Thu Nov 05, 2009 12:10 pm
Vehicle: NA6
Location: Newcastle NSW
Contact:

Re: Stalling once warmed up

Postby NitroDann » Mon Sep 02, 2013 11:15 pm

angusis2fast4u wrote:So as the title suggest my mx seems to stall when the clutch is in, usually is most common when slowing down at the lights. it only really happens once the car is warmed up, i've heard it might be something to do with the choke and raising a float when the water heats up in the vein airflow meter?

Woah, hell no.

and while we're fixing something should i upgrade?

I doubt you will be able to do both at once.

i hear people put RX-7 airflow meters in MX-5's to make them more efficient?

Definitely not, there are oldschool tinkerers like magnablue who play with all sorts of stuff including different afms but not for efficiency and you need a thorough understanding of the whole process before you even start.

would that be the way to go or just pick up a replacement to see if it's good? or clean it out?

It cannot be cleaned, id try a replacement but it could be many things, like a gummed up idle control valve.

also a ticking noise directly related to the speed of the engine.. is that something to worry about? the car has rarely been used until about a month ago, since then has been used "spiritedly" to say it in a nice way..

If its very quiet distinct sharp tick its th einjectors which is normal, if its a louder thrashy tick its the lifters, google 'miata hla'
http://www.NitroDann.com

speed wrote:If I was to do it again, I wouldn't even consider the supercharger.

emily_mx5
Racing Driver
Posts: 1720
Joined: Wed Aug 03, 2011 5:57 pm
Vehicle: NB SE
Location: Sydney

Re: Stalling once warmed up

Postby emily_mx5 » Mon Sep 02, 2013 11:15 pm

google:

miata idle speed droop

and

miata hydraulic lifters

User avatar
Okibi
Speed Racer
Posts: 10899
Joined: Thu Aug 21, 2003 11:00 am
Vehicle: NB SE
Location: Perth, Western Australia
Contact:

Re: Stalling once warmed up

Postby Okibi » Tue Sep 03, 2013 12:06 am

If you had access to a car like this, would you take it back right away? Neither would I.

User avatar
hks_kansei
Speed Racer
Posts: 6154
Joined: Tue Feb 03, 2009 10:43 am
Vehicle: NB8A
Location: Victoria

Re: Stalling once warmed up

Postby hks_kansei » Tue Sep 03, 2013 2:42 pm

Just to clarify for the OP.

It won't be anything to do with a choke, or float.
Those only relate to carbys, not fuel injection.

And even if it was carby fed you shouldn't need to use the choke at all outside of the first start on a cold morning.
1999 Mazda MX5 - 1989 Honda CT110 (for sale) - 1994 Mazda 626 wagon (GF's)

User avatar
Pamex
Racing Driver
Posts: 1366
Joined: Sun Aug 10, 2008 9:28 pm
Vehicle: NA6
Location: SE Melb

Re: Stalling once warmed up

Postby Pamex » Tue Sep 03, 2013 4:36 pm

On carbies, hesitation and revs dropping when you step on the clutch can mean your mixture is too lean, amongst other things.

I'd check it's getting the right mixture of fuel and air.

But yes, as HKS said. It certainly won't be choke or float related.

... unless you've installed carbies... :)
Red 1990 NA | 1949 MG TC. TC 6568 | 244GL Rally Volvo | 1979 HZ Kingswood
"If you can't undestand from wiki, I can't help you." - A wise man

User avatar
angusis2fast4u
Fast Driver
Posts: 313
Joined: Mon Jul 01, 2013 10:48 pm
Vehicle: NB8B
Location: Western Suburbs, Brisbane

Re: Stalling once warmed up

Postby angusis2fast4u » Tue Sep 03, 2013 6:22 pm



Thank you everyone who responded, i tried this method and my idle speed was at about 450-500 i'm guessing when it got this slow it just wanted to kill itself, literally (puns everywhere..) about to go for a test drive and will report back

also if i want to ask more questions under this engines, trans and final drive section should i post new or rename this thread? am new and don't want to annoy people straight up haha
~Angus
2001 Silver NB8B
Past: Grey 1990 Eunos Roadster

User avatar
angusis2fast4u
Fast Driver
Posts: 313
Joined: Mon Jul 01, 2013 10:48 pm
Vehicle: NB8B
Location: Western Suburbs, Brisbane

Re: Stalling once warmed up

Postby angusis2fast4u » Tue Sep 03, 2013 6:24 pm

hks_kansei wrote:Just to clarify for the OP.

It won't be anything to do with a choke, or float.
Those only relate to carbys, not fuel injection.

And even if it was carby fed you shouldn't need to use the choke at all outside of the first start on a cold morning.


Dad might be a bit old school for a miata then hahaha
~Angus
2001 Silver NB8B
Past: Grey 1990 Eunos Roadster

User avatar
hks_kansei
Speed Racer
Posts: 6154
Joined: Tue Feb 03, 2009 10:43 am
Vehicle: NB8A
Location: Victoria

Re: Stalling once warmed up

Postby hks_kansei » Tue Sep 03, 2013 6:27 pm

angusis2fast4u wrote:also if i want to ask more questions under this engines, trans and final drive section should i post new or rename this thread? am new and don't want to annoy people straight up haha


Post a new thread for each new topic.
If there are multiple questions about a similar thing then include them all in one topic.

The main thing is to quickly search the forums before asking, your question may have been asked before and got an answer in the past.
If that turns up nothing, just say "I've searched and couldn;t find an answer, how do I X?"


People here don't tend to get annoyed at people with questions, but they can get annoyed when the same question is asked 100 times (btw, DON'T make a new thread asking about what oil or what tyres. Somebody asks that question about once a month, and it always gets the same asnwers)
1999 Mazda MX5 - 1989 Honda CT110 (for sale) - 1994 Mazda 626 wagon (GF's)

User avatar
angusis2fast4u
Fast Driver
Posts: 313
Joined: Mon Jul 01, 2013 10:48 pm
Vehicle: NB8B
Location: Western Suburbs, Brisbane

Re: Stalling once warmed up

Postby angusis2fast4u » Tue Sep 03, 2013 6:49 pm

This it the ticking sound from the engine

[youtube]http://www.youtube.com/watch?v=XiJeRdyRLmI&feature=youtu.be[/youtube]
~Angus
2001 Silver NB8B
Past: Grey 1990 Eunos Roadster

User avatar
angusis2fast4u
Fast Driver
Posts: 313
Joined: Mon Jul 01, 2013 10:48 pm
Vehicle: NB8B
Location: Western Suburbs, Brisbane

Re: Stalling once warmed up

Postby angusis2fast4u » Tue Sep 03, 2013 8:27 pm

This might get confusing with ticking sound and stalling topics happening at once

in relation to the stalling - the "stalling problem" I'd say is fixed but now on every so often the rev's dip to 250-300, as stated in a previous post i just raised the mechanical idle by turning the screw on the throttle body until it was at ~900 rpm the same as the ECU idle

could this be A/F Ratio? what's your suggestions?
~Angus
2001 Silver NB8B
Past: Grey 1990 Eunos Roadster

93_Clubman
Speed Racer
Posts: 11854
Joined: Mon Aug 08, 2005 11:35 pm
Vehicle: Clubman
Location: Melbourne

Re: Stalling once warmed up

Postby 93_Clubman » Wed Sep 04, 2013 11:56 am

angusis2fast4u wrote:in relation to the stalling - the "stalling problem" I'd say is fixed but now on every so often the rev's dip to 250-300, as stated in a previous post i just raised the mechanical idle by turning the screw on the throttle body until it was at ~900 rpm the same as the ECU idle


Set idle as per:
http://www.miata.net/garage/KnowYourCar/S7_Idle.html

It sounds like you might have improvised after you found it still dipped occasionally after adjusting as per the Miata.net Garage article. If so, this might just compound the issue with occasional high idle. I'd suggest checking the clutch pedal switch as per discussion here:
viewtopic.php?f=29&t=59657

Btw, some background on Angus' 1990 Eunos Roadster:
viewtopic.php?f=29&t=58849&p=741228

mazdaz
Fast Driver
Posts: 364
Joined: Tue Jul 17, 2012 9:41 pm
Vehicle: NC - LE
Location: West Brisbane

Re: Stalling once warmed up

Postby mazdaz » Sun Sep 29, 2013 10:54 am

Trap for new players if you are going to reset the base idle. Ensure your fan control is set to zero as the ecu will compensate if its not.

If the engine cooling fans engage remember that will have an impact as well.

Having said all that I have had a massive improvement. The car no longer feels like it wants to stall.


Return to “MX5 Engines, Transmission & Final Drive”

Who is online

Users browsing this forum: No registered users and 67 guests